Monday, April 14, 2014

Aquaponics, part 3

Ok, so this has taken longer than I expected, but that doesn't mean that I am not enjoying the journey, and the learning as I go. The bigger issue than the time this is taking is that I just have so much that I want to do that sometimes I get sidetracked, and get behind on finishing something that has also been already started.

So anyway, continuing with aquaponics; the system is now just waiting for fish, which I plan to add as soon as the weather warms up. Right now at night, the temperature drops too much for the fish to be comfortable, possibly low enough to kill them. I don't want that to happen, especially since the fish aren't exactly cheap. I'm going to introduce goldfish shortly, then transition to tilapia shortly thereafter. I will have at least some experience with running a system before having to worry about heating it when it gets colder again this winter. I figure that I will at least know enough to have a decent shot at keeping my fish alive, and that's better than I would have right now with warm water fish (tilapia) in cold (well, cool anyway) weather.

So, putting the finishing touches on the system. When we last saw the aquaponics tank, I had cut it down and made the top into the planting area, but had yet to install the water circulation system. Now, it is in, and this is how I did it.

First, the cap from what was once the top of the tank was taken off, and a hole was cut into it. The reason for this is because this cap will now become the spot where the water that is pumped up into the growing area drains back into the fish tank, having been at least partially filtered by the plants, so that the fish are in clean water.


Then a male end pipe is inserted through the hole, and a 'bottom' piece is screwed on the end, which will hold the pipe in position. It doesn't really matter if the seal is water-tight, since this is where water will be passing through anyway; at worst, it will mean that the water drains a little faster than it would otherwise.



 Once that is done, the cap is screwed back onto the upper portion of the container, the 'grow area'.



At this point, I inserted a shorter piece of PVC (about 5" or so) that has had some drain holes/slits cut into it. Holes would be done with a drill; I chose to do slits because I had a saw conveniently at hand, but it really doesn't matter which one is chosen, as long as they actually allow water to drain. At this point, we used another, larger piece of PVC pipe (I believe it was 4"), just slid over this one, as a sort of filter. This will fit right into the cap, and it's function is to keep the grow medium (whatever is used) from clogging the drain holes of this inner pipe. If there is a clog, it should be easy enough to clear on the larger pipe. Also, the larger pipe should be taller than the inner; if there is an issue with the inner pipe clogging, it needs to be shorter so that it can drain through the pipe itself.

At this point, I put in the pump. It doesn't have to be a specific brand, as long as it is capable of pumping water up at least 5 feet. I didn't take a picture of the top portion of the water system, but it is smaller PVC pipe with right turns, creating a square just less than the outer edge of the grow area. The pipe has some holes drilled into it to allow the water pumped up from the fish tank to drain into the grow medium. It is also squared off the allow the water being pumped up from the fish tank to be spread relatively evenly though the grow bed. Even if the coverage isn't that even, the grow medium is something like a sponge in that it will soak up water traveling through or near it, so that the entire grow bed will be saturated.


I will add a last few photos to show the finished system, to include the grow medium. The pump is working fine, the grow medium is saturated, and the weather is to the point that I will be adding fish within a week or two. I am actually planning to use the entire grow bed for strawberries, but if that isn't as successful as I'd like, then I will concentrate on lettuce and probably kale. We'll see what happens...

No comments:

Post a Comment