Monday, March 9, 2015

New project

So, once again, I have started another project. Talking to some guys at work, and one has decided to take the plunge and get some chickens. Not just a few, but he's going all in (well, not literally, but still) and get ten (!) chicks, and raise them for eggs. Naturally, talk turned to coops, and he asked if I could build him a coop. After doing some research, I determined I could, and we discussed what he would need; we decided on a 4x8 coop, raised rather a walk-in.

So, I got to work. I started with the frame, using 2x4x10s, cut down to 9'. The coop itself will be 4x8, and the extra foot will be for the roosting boxes.



Next, I added two more studs so that the floor will be well supported; although this shouldn't end up being extremely heavy, it isn't going to be light either. Once the floor frame was done, I used some 2x4s cut two feet long as legs. Since this is being built in the barn, I felt it would be best to build it near the door, out of the elements, but easy to load onto a trailer when it's done.



Now that the framing and legs were ready, I turned them right-side up, and attached the floor. For this, I used a single sheet of plywood; I have to admit that the size of the coop is perfect, because no cutting was necessary to fit the floor on the frame. You can also see the second piece of plywood that is going to be for the nesting boxes. After attaching the floor, I put on a sealer coat, to make cleaning it easier.



At this point, I framed the long walls, although I call them the front and back. The taller frame is the front, the shorter the rear; the slope on the top of the frames is sloped for the corrugated metal that will be used for the roof. On the front frame, there is the framing for the double door that will be used for cleaning the coop. There is also a 2" opening running the length of the wall, for ventilation.

On the rear wall framing, there is another opening running the length of the wall for ventilation, although this one is 4". There is also framing running the length of the wall, one foot above the floor. There will be two doors there, also used for cleaning, under the roost. That roost will run the length of the coop, and will have four 18"x24" pans under it, to make it easier.


This is where I am now; I started on Saturday, and will hopefully be done by this next weekend. We'll see, but my progress will be documented here...

Saturday, January 31, 2015

"Too busy..."

So, I don't even want to think about how long it's been since I have done anything on here... oy! But, I will say that I have thought about it, but just convinced myself that I was 'too busy'. Yeah, too busy sitting on my butt, watching tv, dorking around doing other things on the computer, doing stuff around the house that I could end up writing about... all that 'too busy'. And of course, my reaction to someone else telling me that they were 'too busy' would be something along the lines of, "that sounds like an excuse, not a reason".

And certainly, in this case, it is.

I said I was too busy, but the bottom line is that I was just being lazy. Mea culpa.


I admit it.

But, here I am again, with the intention of getting back on the ball, and keeping up with this whole deal. I started it because I was excited about some of the stuff that I was doing, and I still am. There are other things that are happening as well, so I need to get into those as well. Basically, there is no shortage of material for a little while at least, so there is no excuse...   lol

So, lately I have been doing some wood working out in the barn, where I usually end up doing some fun stuff. Not always, but let's say more often than not. So what have I been doing? Well, let me put in a little backstory first...

My awesome wife Lisa had a previous marriage, as did I. She has two great kids, her son Marshall and her daughter Jenni. Both are married to some wonderful people, and Jenni now has two beautiful daughters, Eden who just turned three, and Ila, who was born last October. (Someone knows how to actually blog...  http://little-house-in-the-country.blogspot.com) So, I was asked recently to make a small table and chairs for Eden and Ila, and I was very pleased and honored to have that happen. I play around with wood working, but I'm no craftsman, and being given that trust and responsibility for our grandchildren is inspiring.

I've made benches before, and some Adirondack chairs, but this would require a greater skill level and attention to detail, because we can't have little hands getting splinters, or sitting on chairs or at tables that rock by accident. So, I scoured the internet for ideas, wanting to find the right design, and try to get it right, without making Jenni wait too long. (I do believe that I am still behind on two promised child-size Adirondack chairs, but...  shhh.)

Happily, I was successful in finding some plans, and after discussing it with Lisa, we decided to go with this:


The table is 22" high, and the table top dimensions are 22.5" x 32", so it is not particularly large, but should be usable for the girls until they get to be about 6 or so. This was the first time that I actually tried to be 'wood crafty' and make joints that are more than just screws or nails driven through the top or sides, and try to make them hidden for a better look. SO... I researched and found that I basically had two options, a Kreg jig or a biscuit joiner. Being that I have never used (or even seen) a biscuit joiner, although I knew how they worked, I decided to go with the Kreg jig, because I had at least worked with a drill before...  lol

This is how the underside of the table looks, using the Kreg jig and hiding the screws that are holding the table together, legs to the aprons, and top to the aprons as well.


 The horizontal screws in the middle are holding the three boards that comprise the table top together, along with wood glue, and the vertical screws on the sides are holding the table top to the aprons, or body. You can also see some horizontal screws on the aprons that are holding the legs tight; another type of joinery that I've never attempted. Here's another view, that show how using the Kreg jig makes for joints that are clean on the outside, where they can be seen...




 So, what would a table be without chairs? Another first, I made child-size chairs to go with the child-size table. I've only finished one at the present time, but... I wanted to get started on here, and couldn't wait! LOL Actually, both Lisa and I have been a bit under the weather of late, so the chairs have come along a bit slower than I would have preferred, but the work is getting done, slowly but surely...


I put the 45 gallon can next to the table to get a little perspective on it. The seat on the chair is 14" high, which I think should be fine for some time, and the actual seat dimensions are 12.5" x 13.75", so it is small enough for them, but juusst big enough for an adult to sit if they need to. I will make two, maybe three chairs, and they should all be able to stack on each other; the rear leg is outside the dimension of the seat, and the front leg is within it, so they should stack three high without much problem. At least, that's the plan; without three chairs to test it, I can only say for sure that two would stack. And, they are actually pretty light; I haven't weighed them, but I'd guess at no more than about 5 lbs, so the girls should be able to get to move them about without needing much assistance.

After the next chair is finished, Jenni has picked out a stain for them, which I will follow up with a sealer, probably polyurethane, but I might go with a spar varnish. I really do want to seal the table top and the seat portion of the chairs, since the girls are still so little.

That will be a follow-up post, another one that will need to be done. See, there really is stuff to write about; I just have to do it...



Wednesday, May 28, 2014

Score!

So, if you've been reading this blog, I have wanted to become a little more self-sufficient, and to grow some items in a garden to eat, among other things. So, we have been working on that, and we have been successful!

It has been quite a nice few weeks lately, because our garden has been fairly bountiful. While our tomatoes and peppers have come along rather slowly (we have yet to get anything from them, but they are starting to show what is in store), our carrots and cucumbers have come along at what seems to be a normal pace, and explosively, respectively. The carrots were harvested today, and this is some of the harvest:


Not as big as I'd hoped, but they are nicely shaped, and I think (hope!) that they will taste as great as the ones we had last year. It's just so funny, that they taste like carrots, only more so! lol

As for cucumbers, we planted about 20 seeds, but four or five plants just took off, and choked out all the others. By doing that, they had the run of the bed, so to speak, and they just went crazy! We have harvested about 65-70 cukes off those 4-5 plants, and they have been a nice size and shape. Since we weren't going to eat that many in salads, we turned to the next best thing: pickles! We do love pickles, Lisa even more than me, so it seemed to be a logical choice to try our hand at them.

This was our first effort at any sort of canning, although we have both wanted to try it (me more than her, in this case). So even though we didn't have a pressure cooker, we found out how to do 'icebox pickles', which don't require pressure canning. Actually, to be honest, it was really Lisa who did the work on that; she not only found out how, but found the recipe, and did the work.

Suffice to say that the pickles were a huge success! We loved them, and so I took some to work with me, which I let some guys taste-test; not only did they like them, they wanted to buy jars of those pickles, that's how good they are! So, we have been making pickles and laughing about how funny it is that we can make something that tastes so good, using our own produce, because neither of us ever thought of something like that happening.

Here are some examples of what we have made so far:



Lisa made the slices, I made the spears.

A little story: when Lisa's daughter was very young, she LOVED pickles! There were times when Lisa would go into the kitchen, and there was Jenni, trying to open the refrigerator door, but just wasn't big enough to. She would then turn to Lisa and say, in a plaintive voice, "Pudoh, pudoh", which was her trying to say 'pickle, pickle'. I remembered that story, and joked with Lisa that I thought that we may have to call our efforts 'Pudoh's Pickles'... the more I thought about it, the more I believe it would be a good name.

I'm off to crunch on some more right now...

Monday, April 14, 2014

Aquaponics, part 3

Ok, so this has taken longer than I expected, but that doesn't mean that I am not enjoying the journey, and the learning as I go. The bigger issue than the time this is taking is that I just have so much that I want to do that sometimes I get sidetracked, and get behind on finishing something that has also been already started.

So anyway, continuing with aquaponics; the system is now just waiting for fish, which I plan to add as soon as the weather warms up. Right now at night, the temperature drops too much for the fish to be comfortable, possibly low enough to kill them. I don't want that to happen, especially since the fish aren't exactly cheap. I'm going to introduce goldfish shortly, then transition to tilapia shortly thereafter. I will have at least some experience with running a system before having to worry about heating it when it gets colder again this winter. I figure that I will at least know enough to have a decent shot at keeping my fish alive, and that's better than I would have right now with warm water fish (tilapia) in cold (well, cool anyway) weather.

So, putting the finishing touches on the system. When we last saw the aquaponics tank, I had cut it down and made the top into the planting area, but had yet to install the water circulation system. Now, it is in, and this is how I did it.

First, the cap from what was once the top of the tank was taken off, and a hole was cut into it. The reason for this is because this cap will now become the spot where the water that is pumped up into the growing area drains back into the fish tank, having been at least partially filtered by the plants, so that the fish are in clean water.


Then a male end pipe is inserted through the hole, and a 'bottom' piece is screwed on the end, which will hold the pipe in position. It doesn't really matter if the seal is water-tight, since this is where water will be passing through anyway; at worst, it will mean that the water drains a little faster than it would otherwise.



 Once that is done, the cap is screwed back onto the upper portion of the container, the 'grow area'.



At this point, I inserted a shorter piece of PVC (about 5" or so) that has had some drain holes/slits cut into it. Holes would be done with a drill; I chose to do slits because I had a saw conveniently at hand, but it really doesn't matter which one is chosen, as long as they actually allow water to drain. At this point, we used another, larger piece of PVC pipe (I believe it was 4"), just slid over this one, as a sort of filter. This will fit right into the cap, and it's function is to keep the grow medium (whatever is used) from clogging the drain holes of this inner pipe. If there is a clog, it should be easy enough to clear on the larger pipe. Also, the larger pipe should be taller than the inner; if there is an issue with the inner pipe clogging, it needs to be shorter so that it can drain through the pipe itself.

At this point, I put in the pump. It doesn't have to be a specific brand, as long as it is capable of pumping water up at least 5 feet. I didn't take a picture of the top portion of the water system, but it is smaller PVC pipe with right turns, creating a square just less than the outer edge of the grow area. The pipe has some holes drilled into it to allow the water pumped up from the fish tank to drain into the grow medium. It is also squared off the allow the water being pumped up from the fish tank to be spread relatively evenly though the grow bed. Even if the coverage isn't that even, the grow medium is something like a sponge in that it will soak up water traveling through or near it, so that the entire grow bed will be saturated.


I will add a last few photos to show the finished system, to include the grow medium. The pump is working fine, the grow medium is saturated, and the weather is to the point that I will be adding fish within a week or two. I am actually planning to use the entire grow bed for strawberries, but if that isn't as successful as I'd like, then I will concentrate on lettuce and probably kale. We'll see what happens...

Saturday, March 15, 2014

Latest project, a truck bench

Well, I'm calling it a truck bench, because it's a bench with a truck tailgate as the backrest. I saw one recently, thought it was a cool idea, and decided that I was going to make one for myself. I was already going to a junkyard (excuse me, Pull A Part) to get something, so I went looking for a truck tailgate. I found one that I was okay with, but decided to check just a few more on my way out, and found one that I thought was perfect. Here it is, after I've sprayed it with a flat clear coat to make sure it lasts longer in whatever weather it sees. I'm guessing the previous owner of the truck painted it himself, but I thought it fit just right, even though the paint job isn't the greatest...


 It really didn't take all that much lumber. The legs are 4x4's, the seat is 2x6's, and the frame, arms, and back supports are 2x4's. I didn't have a blueprint, so I ended up using more wood than I actually needed to, but that's the problem with just winging it, as I was doing in this case. I suppose that if I were a better woodworker, with more experience, I wouldn't run into issues like this, but as far as I know, there's only one way to get that experience. Anyway, here is the wood before I started, just cut to size.


This is all of what I should have needed; as I said, the wood used ended up being a little bit more. Since  the bench is going outside, I felt as though I needed to do something to protect the wood; I decided that staining it was preferable to painting it, so that is what I did.

Note the Shamrock shake that Lisa brought me :)

I did measure the wood right, and notched the front seat board correctly, but forgot that there was supposed to be a slight gap between the front leg and that notch, so that the legs were closer together than they should have been. Enough that the tailgate didn't quite fit in, anyway. That didn't turn out to be a big problem, since I was able to cut and chisel out enough to fit in the tailgate. In the end, that worked out better, since the back braces for the tailgate (one upper, one lower) lock the tailgate into position without having to drill holes for bolts to do the same thing.


You can see that the backrest is angled somewhat, so that it is more comfortable to sit in. Although I suppose that using the other side of the tailgate might be an idea, since it isn't angled, I liked the idea of having the name facing out better.


Another project done. That's a good feeling, and one that I need to work on having more often... lol

Wednesday, March 12, 2014

Raised beds, part 1


So, I have come to the conclusion that I don't have to have complete projects in order to talk about them, since it can take me a while to finish a project sometimes. Between work, wanting to spend time alone with Lisa, and sometimes just feeling lazy, everything doesn't always come together quickly, so waiting until something is finished might mean not talking about it for longer than I'd like... lol

I've mentioned that I am working on some more raised beds for the garden, and I am doing so. 'More', though, means that I have some, which I do. I made these last year, and they worked well enough; they are 4x8x2, and the soil is a 40/40/20 mix of garden soil, topsoil, and compost. I chose to not use plain dirt for a simple reason: most of the soil here in south Texas kinda sucks. There is a lot of clay in many areas, as well as something called 'black earth', which helps form caliche. For those who haven't heard of caliche, it is when soil becomes hardened and prevents water saturation, as well as making the soil too much of a base to provide good nutrition to plants. So, little wonder that I wanted to avoid working with native soil! Anyway, the soil that is in the beds has worked well so far; not only were we able to grow in it, but it remained fairly soft over the winter, and we have had little problems so far with having to weed. We'll see how well that continues. I have already planted in the current beds; tomatoes, cucumbers, peppers, and carrots. This is what the 'old' beds look like:





I am in the process of making two more beds, although I am using some materials that I happen to have on hand rather than buying 8x12's. I am using some 2x4's, buying a few 4x4's, and cutting up some corrugated metal panels that I was able to scrounge up from people that were in the process of tearing down an old barn. I am using the same dimensions of 4x8x2, because it seems to be a really good size, large enough to grow plenty of a crop in, without being so big that we can't reach any spot in the bed easily. It is also easier on the back than bending all the way down to work the ground; right now, that really isn't that much of a deal, but as I get older, I can imagine that it will be a blessed bonus. We are currently splitting the beds in half, planting two crops in one, but as we enlarge the garden, the plan is to use each one for a different crop. Of course, that will depend on how big the garden gets; the plan is to make it a little larger every year, until it starts to feel too much like work to take care of. At that point, we will stop enlarging, and work with what we have. I'm thinking that we will get to at least 10 beds, but as with so many things, time will tell.

Anyway, this is what the first partially constructed bed is looking like.





In this version, I'm using ends and middles of 4x4's, with 2x4's as the bracing that connects them, and that the corrugated metal is attached to. The construction is fairly simple, and I think it should be more than strong enough to hold up against the weight of the soil when it gets added. I added some small braces on the middle of the supports, just in case; I'm one of those people who worry about stuff like that. I figure, better to have it and not need it than need it and not have it. Because the slowest part of this construction is the measuring of the corrugated panels so that they can be cut to the right length, I'm considering putting in a single length of corrugated metal, and attaching the middle brace afterwards, with the metal between the brace and the support. If that happens, I'll take some more pictures to show how that worked, or didn't. I could have trimmed the bottom edge that you can see in the pictures, but I think that it will be fine just tucking it under, and work towards keeping grass from growing in through the bottom. 

Underneath, and you can see just a bit of it in the photos of the finished beds, I cut up an old pool liner to keep the tough, weedy, hard to kill grass that lies under the bed from growing up and choking out our vegetables, as well as cutting a 4x8 section of animal fencing (which is stronger than chicken wire, consisting of stronger wire in 1" x 3" rectangles) in order to keep moles and whatnot from burrowing up into the beds and chowing down. Since I don't have any more of that liner left, I'll be putting a double layer of weed mat down instead. In the background of the top photo, you can see the small fence that I put up to keep out rabbits; if deer become an issue, then I will have to raise the fence and look into a solar-powered electric fence. So far, though, even though there are some deer in the area, they have not been a problem in the garden; the dogs may be earning their keep in that regard.

As for the soil, while I have been quite happy with the performance of the mix, the drawback is that it is more expensive than I'd like, considering that it takes about 40 bags to fill a bed. So, I started researching what I could do to create better soil, cheaper. What I found is that the best soil for growing is called sandy loam, which is 60% sand, 25% silt, and 15% clay, or thereabouts. I'm going to bring in a truckload of soil, test it, and add sand as needed to create something near that balance, so that I can use it for any beds that are created in the future. Bringing in about 5 yards of soil will only cost about $150, and sand is not expensive either. It may not be feasible for a large farm, but on a small scale, I think it's definitely do-able. Besides, whatever soil isn't used can be put to use creating a berm for a gun range in the back yard.

There are definitely advantages to living outside city limits...

Saturday, March 8, 2014

Resurrection

Okay, I've been goofing off, I admit it. I've been enjoying lazing about, doing this and that, but not really doing much other than just letting the days pass. But, since spring is almost here, I've been having to get ready for it, by getting things around the house done. I've had to turn the earth in the raised beds, I need to make some more raised beds for the growing season, I need to get the tiller running (grrr!) to be able to plant what the Indians called 'the trinity' of corn, peas, and squash. I also have some projects around the house to do, as well as work on the object of this post, my truck.

A little background on this...

We bought a 1987 GMC pickup while we were in New Mexico, because I love old trucks, and it would/could/should come in handy as well. There was a younger guy down the street from us that was selling this truck, as it turned out because he needed money to get married. We saw the For Sale sign on it when we took the dog out for walks, and I had commented on how I liked the way it looked, so when we saw him outside one day as we were walking past, we struck up a conversation. Later that day, 'the beast' was parked in front of our house...




It was a popular truck, lots of people said that they loved it, and wanted to know if I wanted to sell it. Um, nope. I worked on this and that, and it was really coming along well. One of the last things that I did was decide to make the change from fuel injection (1987 was the first year that Throttle Body Injection was standard on all GMC/Chevy trucks) and go to using a carburetor. I decided to have the engine rebuilt while I was at it, which took a couple of tries, but this was the end result.


A nice look, but ultimately, it was my downfall. 

As it turned out, there was a developing problem with the fuel system. As I had it explained to me, instead of 5.5-6 psi, the fuel pump was running well over 12 psi, which overloaded the fuel line, so that it eventually split right near the carb. As you can imagine, fuel spilling onto a hot engine is not a good thing, so I took it to the a shop, where they said it was fixed. 

Turns out, not so much.


This was the scene as I drove home from the shop; I didn't even make it to the house, which is less than 10 miles away. Luckily, nobody was hurt. This is actually only about 100 yards from the house; I had seen Lisa's car parked at the neighbor's house, and realized that I didn't have either the garage door opener or the house key (both taken out of the truck since it was in a shop), so I was going to stop and get one or the other so that I could get into the house when the truck sputtered and died. It didn't start again, so I was getting out to take a look at the engine, when I saw flames coming from under the hood. Needless to say, the truck didn't survive.

*sigh*

After dealing with the insurance, I started to look around for another truck. I wanted another older truck that would fill the same purpose, something that I could use to haul stuff around, but that was reliable and that still looked good; I wasn't exactly wanting a 'farm truck'. I was pleasantly surprised to find that there were a number of options, although none in the immediate area. I did find what I was looking for about four hours away, and went up to take a look at it. Arrangements were made, and I am now driving this one, not 'the beast', but I'm calling her 'Belle'. For those who live in Texas and the surrounding area, the name and color may make sense... lol


This is also a 1987, but a Chevrolet rather than a GMC. It has been lowered, which I will eventually address, but the engine and transmission have been rebuilt (although I will swap out the Turbo 400 that is currently in it for the 700R from the old truck, for the overdrive), as well as the differential. The engine is still injection, and I think that I will stay with that. The interior is in about the same shape, and the body is straight with minimal underbody issues. It is almost a clone of the last one, so I am enjoying it, just in a slightly different way.

I'm already doing work on this truck, because old trucks and cars are never really done, just like a house. That's okay, it just gives me something to do, since there isn't enough now...  lol  The push bumpers were added, I have a new seat on the way, and I'm getting ready to put in a new exhaust (headers, tubing, and Flowmasters).

It's kind of funny, because this truck is actually in a little better shape overall than my last. I felt like crap watching the Beast go up in flames, but it turned out to be a good thing overall; I got a better truck, mechanically, and it ended up not costing me a dime. I guess that life works like that in a lot of different ways; what we think is going to be an awful situation or happenstance turns out to be a blessing in disguise.

Something to remember...